[
Date Prev][
Date Next][
Thread Prev][
Thread Next][
Date Index][
Thread Index]
[
List Home]
Re: [sumo-user] different number of vehicles in different edges
|
Thank you Michael.
So, in case I use the flows I sent you, could you please confirm that when, for example, I define the flow id 2 (from=“3"to=“4” vehsPerHour=“200”)
it means that these vehicles run only in the specific edges. That is to say, that they don’t insert the network from the beginning (i.e. edge 1), right?
Best regards,
Natalia
> On 5 Nov 2018, at 08:26, Michael Behrisch <oss@xxxxxxxxxxx> wrote:
>
> Hi Natalia,
> both your definitions and the output are correct. The output gives the
> total number of vehicles not the average. If all your edges are
> consecutive you might want to define the vehicles to run all the edges
> to have less insertions. Something like this:
>
> <flow id=“1" type="1" from="1" to=“10" begin="75600" end="79200"
> vehsPerHour=“100" departLane="best" departSpeed="max"/>
> <flow id=“2" type="1" from=“3" to=“10" begin="75600" end="79200"
> vehsPerHour=“80" departLane="best" departSpeed="max"/>
> <flow id=“3" type="1" from=“3" to=“4" begin="75600" end="79200"
> vehsPerHour="20" departLane="best" departSpeed="max"/>
> <flow id=“4" type="1" from=“7" to=“10" begin="75600" end="79200"
> vehsPerHour=“50" departLane="best" departSpeed="max"/>
> <flow id=“5" type="1" from=“9" to=“10" begin="75600" end="79200"
> vehsPerHour=“20" departLane="best" departSpeed="max"/>
>
> Best regards,
> Michael
>
>
> Am 03.11.18 um 16:21 schrieb Natalia Liora:
>> Hello,
>>
>> I want to run a simulation in which I have 10 road segments (edges).
>> Along specific edges I want to define that different number of vehicles
>> run each edge.
>>
>> In rou.xml file I define the above flows as following
>>
>> <flow
>> id=“1"type="1"from="1"to=“2"begin="75600"end="79200"vehsPerHour=“100"departLane="best"departSpeed="max"/>
>> <flow
>> id=“2"type="1"from=“3"to=“4"begin="75600"end="79200"vehsPerHour=“200"departLane="best"departSpeed="max"/>
>> <flow
>> id=“3"type="1"from=“5"to=“6"begin="75600"end="79200"vehsPerHour="180"departLane="best"departSpeed="max"/>
>> <flow
>> id=“4"type="1"from=“7"to=“8"begin="75600"end="79200"vehsPerHour=“230"departLane="best"departSpeed="max"/>
>> <flow
>> id=“5"type="1"from=“9"to=“10"begin="75600"end="79200"vehsPerHour=“250"departLane="best"departSpeed="max"/>
>>
>> With the above flows I want to define the following
>> from edge 1to 2 100 vehicles running. In the following, the vehicles
>> increase to 200 until the edge 4. Then, the vehicles decrease to 180
>> until the edge 6 etc.
>>
>> I understand that with the above flows I do not get the desired vehicle
>> flows since in the summary output I get that 960 vehicles have been
>> loaded while the real average number of loaded vehicles should be 192.
>>
>> Could you please tell me how I have to define the flows?
>>
>> Thank a lot
>>
>> Natalia
>>
>> _______________________________________________
>> sumo-user mailing list
>> sumo-user@xxxxxxxxxxx
>> To change your delivery options, retrieve your password, or unsubscribe from this list, visit
>> https://www.eclipse.org/mailman/listinfo/sumo-user
>>
>
>