I’m sorry, unfortunately I’m not a sales representative of the company.
You should probably follow the references in the page linked in the previous message to get proper assistance.
Best regards,
Matteo
--
Matteo Maiero
Senior Software Engineer
direct: +39 0433 485 902
email: matteo.maiero@xxxxxxxxxxxx
EUROTECH
Imagine.Build.Succeed.
HEADQUARTERS
EUROTECH S.p.A. – Via Fratelli Solari, 3/a | 33020 Amaro UD | Italy | Tel. +39. 0433 485411 | Fax +39. 0433
485499 |
Cap. Soc. 8.878.946,00 € I.V. | P.IVA / C.F.: IT 01791330309 | REA Udine 196115
www.eurotech.com
____________________________________
Il presente messaggio ed ogni suo allegato sono da intendersi inviati esclusivamente agli effettivi destinatari e potrebbero essere soggetti a restrizioni legali. Se
avete ricevuto questo messaggio per errore vi invitiamo a darne immediata notifica al mittente e cancellarlo dal vostro sistema. Qualsiasi altro uso di questo messaggio da parte vostra e' strettamente proibito.
This e-mail, and any file attached to it, is meant only for the intended recipient of the transmission and may be a communication privileged by law. If you have
received it in error, please notify the sender immediately and delete the original from your system. Any other use of this e-mail by you is strictly forbidden.
From:
Shankar, Ramraj <Ramraj.Shankar@xxxxxxxx>
Date: Thursday, 6 May 2021 at 16:26
To: Kura Developers mailing list <kura-dev@xxxxxxxxxxx>
Cc: Maiero, Matteo <matteo.maiero@xxxxxxxxxxxx>
Subject: Re: ESF Fanuc Driver
Hello Mr. Mairo,
Thank you for your reply.
I am planning to purchase the driver.
Could you please guide me through its features? I would like to have a trial as well.
From: kura-dev <kura-dev-bounces@xxxxxxxxxxx> on behalf of Maiero, Matteo via kura-dev <kura-dev@xxxxxxxxxxx>
Sent: 06 May 2021 16:16:16
To: Kura Developers mailing list
Cc: Maiero, Matteo
Subject: Re: [kura-dev] ESF Fanuc Driver
Hello,
The Fanuc Driver supports the following Fanuc controllers:
-
FANUC Series 30i /31i /32i /35i-MODEL B
-
FANUC Series 31i-MODEL B5
-
FANUC Power Motion i-MODEL A
-
FANUC Series 0i-MODEL D/F
Be careful that the ESF Fanuc driver is a bundle with commercial license protected by an EULA: https://marketplace.eclipse.org/content/esf-fanuc-driver
Best regards,
Matteo
--
Matteo Maiero
Senior Software Engineer
direct: +39 0433 485 902
email: matteo.maiero@xxxxxxxxxxxx
EUROTECH
Imagine.Build.Succeed.
HEADQUARTERS
EUROTECH S.p.A. – Via Fratelli Solari, 3/a | 33020 Amaro UD | Italy | Tel. +39. 0433 485411 | Fax +39. 0433
485499 |
Cap. Soc. 8.878.946,00 € I.V. | P.IVA / C.F.: IT 01791330309 | REA Udine 196115
www.eurotech.com
____________________________________
Il presente messaggio ed ogni suo allegato sono da intendersi inviati esclusivamente agli effettivi destinatari e potrebbero essere soggetti a restrizioni legali. Se
avete ricevuto questo messaggio per errore vi invitiamo a darne immediata notifica al mittente e cancellarlo dal vostro sistema. Qualsiasi altro uso di questo messaggio da parte vostra e' strettamente proibito.
This e-mail, and any file attached to it, is meant only for the intended recipient of the transmission and may be a communication privileged by law. If you have
received it in error, please notify the sender immediately and delete the original from your system. Any other use of this e-mail by you is strictly forbidden.
From:
kura-dev <kura-dev-bounces@xxxxxxxxxxx> on behalf of Shankar, Ramraj <Ramraj.Shankar@xxxxxxxx>
Date: Thursday, 6 May 2021 at 16:09
To: kura-dev@xxxxxxxxxxx <kura-dev@xxxxxxxxxxx>
Subject: [kura-dev] ESF Fanuc Driver
Hello,
I am working on a project to get data from Fanuc controller.
I would to know if ESF Fanuc driver in Kura would be useful for this.
Thank you,
Ram.
|